為了安全作業需要注意以下幾點： 1、用鋸的重量來控制切割壓力。對于較軟的材料來說，這樣的重量已經足夠。過多的壓力會降低鋸片的速度。對于較硬的材料，可以通過加壓的方式來降低鋸片的轉動速度。切割是保持鋸筆直。鋸片的任何扭曲或歪斜都可能降低其使用壽命 2、關閉電源時，釋放閥桿。 3、更換鋸片前，務必?cái)嚅_電源。 4、順時針轉動調整手柄以便釋放鋸片導桿上的張力。然后釋放側面板的鎖以便打開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開。 5、下次切割開始前，鋸片必須保持運動狀態。電動鋸時，鋸片不能接觸任何表面。 6、了解所需切割的材料。 7、確保牢固固定了所需切割的材料，防止其移動。 8、接電源時，用手指按壓閥桿，然后開始切割。 9、斷開電源時，關閉電源軟管閥。斷開前，先打開電源閥給軟管減壓。
故障排除： 故障 可能的原因 馬達運轉正常，但是切割效率低下 1、鋸片不夠鋒利。更換鋸片。 2、鋸齒指向不對。改變鋸齒方向。 3、鋸片不夠緊固。緊固鋸片。 4、切割速度不對。提高或降低電源流動壓力。 振動 1、要切割的材料沒有穩固好。夾緊切割位置附近的材料。 馬達不能啟動 1、電源供給不足。
Method of use: 1, what's needed to cut materials. 2, to ensure the required fixed cutting material, to prevent the mobile. , 3 power supply connected, pressing with a finger and began cutting stem. 4, saw the weight to control the cutting pressure. This weight is enough for softer materials. Too much pressure can reduce the speed of the saw blade. For harder materials, the speed of rotation of the saw blade can be reduced by pressure. The cutting is to keep the saws straight. Any twist or skew of the sawblade may reduce its service life. (notice: avoid debris that may fall after cutting. When the cutting is about to be finished, do not make the saw touch your body, the workpiece, or the other people in the vicinity. 5, before the start of the next cut, the blade must keep moving. When an electric saw is used, a saw can not contact any surface. 6, replacing the saw blade, you must disconnect the power supply capacity. 7, clockwise rotation adjustment handle to release the tension on the saw blade guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod. Contact gold manager phone 13934240041